Asme Ptc 19.2 Trial Process Instruments#

ASME PTC 19.5-2004 (R2013) Flow Measurement ASME PTC 19.2-2010 (R2015) Pressure Measurement Instruments and Apparatus Supplement Performance Test Codes. General Documents on Measurement of Process Parameters and Associated Phenomena. (PTC 19.2), Pressure (19.3) and Fluid F low (PTC 19.5 recently updated).TAMILNADU GENRATION AND DISTRIBUTION CORPORATION LIMITED.ASME PTC 19.1-2013 Test Uncertainty. Each document has a standard format, beginning with an Object and. Color enhanced smoke trail showing von Karman Vortex Street in laminar fluid flow (1) 1.2 Brief history of ASME PTC 19.3 The standard dates back to 1957 when ASME (American Society of Mechanical Engineers)What is in an ASME PTC Physically, a PTC is a soft cover, 8.5 by 11 inch document ranging from 10 to 300 pages in length. Thermowell failures in their systems, but ASME PTC 19.3-1974 had been the standard by which most thermowells were designed.

No: PE-TS-412-166-A001AMENDMENT NO. FOLLOWING INSTRUMENTS SHALL ALSO BE PROVIDED IF NOT SHOWN SPECIFICALLY IN PID:A) DUAL REDUNDANT PRESSURE TRANSMITTERS SHALL BE PROVIDED AT DISCHARGE HEADER OF HFO PUMPS REQUIRED FOR INTERLOCK & PROTECTION.B) DUAL REDUNDANT RADAR TYPE LEVEL TRANSMITTERSSPEC. CODES FOR DESIGN, INSPECTION AND SERVICE FOR C&I ITEMS SHALL BE AS PER ANNEXURE I TO THIS AMMENDMENT.4.0 P&ID FOR HFO SYSTEM, # PE-DG-412-166-A1011. AUX STEAM FOR FLOOR COIL HEATER (ON/OFF TYPE) CONTROL VALVE AND AUX STEAM FOR SUCTION HEATER (MODULATING) CONTROL VALVE.2.0 1.0(INSTRUMENTAION & CONTROL) SECTION C ANNEX I, PAGE NO 34 OF 487.ALL PRIMARY INSTRUMENTS, HARDWARE & JBS ETC USED FOR MEASUREMENT FOR HFO AND LDO SYSTEM SHALL BE FLAME PROOF (IEC-79.1, PART I).APPLICABLE STANDARD FOR MAJOR ITEMS HAVE BEEN MENTIONED AT ANNEXURE II, SECTION C OF TECHNICAL SPECIFICATION. BIDDER TO NOTE THAT EXISTING DISCRIPTION AS APPEARING IN THE SPECIFICATION STANDS DELETED / MODIFIED OR ADDED AND CLAUSES / DETAILS AS MENTIONED IN AMMENDMENT (TO BE READ AS) COLUMN SHALL BE APPLICABLE AND COMPLIED BY THE BIDDER.CONTROL VALVES FOR FUEL OIL TEMPERATURE CONTROL I.E. - 1 DATE SHEET 1 OF 3AMENDMENT / ADDITION TO EXISTING CLAUSES OF FOHS TECHNICAL SPECIFICATION.

- 1 DATE SHEET 3 OF 3REQUIREMENT CHAPTER FOR PERFORMANCE GUARANTEE TO BE ESTABLISHED BY SUCCESSFUL BIDDER IS ATTACHED AS ANNEXURE II TO THIS AMMENDMENT.8.0 PG.NO. No: PE-TS-412-166-A001AMENDMENT NO. 94 OF 487.6.0 P&ID FOR STEAM AND CONDENSATE FOR HFO HEATING AND TRACING, #SPEC. 94 OF 487.E) EACH PUMP PROVIDED IN OIL WATER SEPARATOR PIT AND SUMP SHALL BE PROVIDED WITH PRESSURE SWITCH AT DISCHARGE FOR INTERLOCK & ALARM.5.0 P&ID FOR HSD SYSTEM, # PE-DG-412-166-A102.B) LEVEL SWITCHES SHALL BE PROVIDED ON EACH FUEL TANK AS PER TECHNICAL SPECIFICATION SECTION C, ANNEX VIII, CL.

The Bidder shall fully acquaint himself with these requirements and shall ensure compliance with them.The equipments, systems and services furnished as per this specification shall conform to the codes and standards mentioned in Cl. Climate is tropical conductive to fungus growth.Dust particles Heavily dusty with abrasive dust and coal particles of size 5 to 100 microns present in the atmosphere in large quantity.1.08.00 CODES AND STANDARDS 1.08.01 All equipments, system and service covered under this specification shallComply with the requirements of the latest statutes regulations and safety codes as applicable in the locality where the equipments/systems will be installed. Tropical protection shall conform to IS:3202 entitled 'Climate Proofing of Electrical Equipment' or BI:CP-1014:1963 entitled 'Protection of Electrical Power Equipment Against Climatic condition'.Gases and fumes Sulphur dioxide and/or trioxide fumes mildly present. All equipment supplied against this specification shall be given tropical & fungicidal treatment in view of the severe climatic conditions prevailing at site as described under project data.2. REPLIES TO PRE-BID QUERIES ARE ATTACHED AS ANNEXURE IV TO THIS AMENDMENT AND SHALL BE BINDING ON BIDDER.DESEIN Vol-V : Instrumentation & Control Works2 x 660 MW ENNORE SEZ Supercritical Thermal PowerProject at Ash Dyke of NCTPS1. 2SIZE: 50 NB X8 M LONG FOR CONDENSATE SERVICE.SIZE: 25 NB X8 M LONG FOR CONDENSATE SERVICE.9.0 ADDITION SPECIFICATION FOR ELECTRIC HEATTRACING IS ATTACHED AS ANNEXURE III TO THIS AMENDMENT.1.

MOEF, Inspectors of factories, IBR, TAC, BEE, CPCB/TNPCB etc) with regards to various plants areas like Main plant, Fuel oil plant/system, Chlorination Plant, Fire Fighting system, Emission Measurement, Ambient Air Monitoring system etc. It shall be the responsibility of the Bidder to obtain the necessary approval of the concerned Inspecting Authority/Chief Inspector of Boilers for the design and design calculations and manufacturing and erection procedures as called for under the IBR act for all items requiring such certifications.The requirements of statutory authorities (e.g. Thedecision of the Owner shall be final and binding in all such cases.The Bidder's scope of supply shall include some items such as thermowells, and other in-line devices for main steam, hot reheat, cold reheat, feed water system falling under the purview of Indian Boiler Regulation (IBR) Act.

RTD Design Code DIN EN 60751:1996, BS EN 60751 : 20086. Thermometer-element-platinum resistance-IS-2848, IEC 751/DIN 437605. Temperature measurement by electrical resistance thermometers - IS-2806.4. Temperature measurement - Thermocouples ANSI-MC 96.1 1982, IEC 5843. Performance Test Code for temperature measurement ASME PTC 19.3 (1974 R 1998)2. Bidder to note that in no case, OEM/manufacturers own standards shall be accepted.1.

Asme Ptc 19.2 Trial Process Instruments

Dynamic response testing of process control instrumentation - ANSI MC 4.1(1975): ISA-S26 (1968). Compatibility of analog signals for electronic industrial process instruments -ISA-S 50.1:ANSI MC 12.1 - 1975.4. Safety requirements for electrical and electronic measuring and controllingInstrumentation - ANSI C 39.5 - 1974.3. Automatic null balancing electrical measuring instruments - ANSI C 39.4 (Rev.1973), IS 93192. Bourdon tube pressure and vacuum gauges - IS 3624, IS 3602, ASME B 40.11.08.02.03 Electronic measuring Instruments & Control hardware1. Performance Test Code for pressure measurement - ASME PTC 19.2 (2010)2.

Requirements and methods of testing of wire wrap terminations DIN 41611Part-2.10. Edge socket connectors - IEC 130-11.9. General requirements and tests for printed wiring boards - IS 7405 (Part-I) - 19738. Printed circuit boards - IPC TM-650, IEC 326 C7.

Contact rating - AC services NEMA ICS Part-2 125, A6002. Direct acting Electrical Indicating Instruments: IS-1248-1968.1.08.02.04 Instrument Switches and Contacts1.